Asphalt, Paving & Construction
  • Print
  • Bookmark

Glossary

Glossary of Terms: Asphalt and Paving

A

Absolute Viscosity

A measure of the viscosity of asphalt with respect to time, measured in poises, conducted at 60 degrees C (140 degrees F). The test method utilizes a partial vacuum to induce flow in the viscometer.

Aggregate Storage Bins

Bins that store the necessary aggregate sizes and feed them to the dryer in substantially the same proportions as are required in the finished mix.

Aggregate

A collective term for the mineral materials such as sand, gravel, and crushed stone that are used with a binding medium (such as water, bitumen, portland cement, lime, etc.) to form compound materials (such as asphalt concrete, portland cement concrete [PCC].etc.)

Aggregate Trucks

Trucks equipped with hydraulic lifts to dump the aggregate into the spreader or storage area.

Aggregate Spreaders

Machines used for spreading aggregate evenly at a uniform rate.

Air Voids

Internal spaces in a compacted mix surrounded by asphalt-coated particles, expressed as a percentage by volume of the total compacted mix.

Alligator Cracks

Interconnected cracks forming a series of small blocks resembling an alligator's skin or chicken wire and caused by excessive deflection of the surface over unstable subgrade or lower courses of the pavement.

Asphalt Tack Coat

A relatively thin application of asphalt binder applied to an existing asphalt concrete or portland cement concrete (PCC) surface at a prescribed rate. Asphalt emulsion diluted with water is the preferred type. It is used to form a bond between an existing surface and the overlying course.

Asphalt Emulsion Mix (Warm)

A mixture of asphalt emulsion and mineral aggregate usually prepared in a conventional hot mix asphalt plant at a temperature below 95 degrees C (200 degrees F). It is spread and compacted at a temperature above 65 degrees C (150 degrees F).

Asphalt Pavements

Pavements consisting of a surface course of asphalt concrete over supporting courses such as asphalt concrete bases, crushed stone, slag, gravel, portland cement concrete (PCC), brick, or block pavement.

Asphalt Distributor

A truck or trailer having an insulated tank, heating system, and distribution system. The distributor applies asphalt to a surface at a uniform rate.

Asphalt Emulsion

An emulsion of asphalt binder and water that contains a small amount of an emulsifying agent. Emulsified asphalt droplets may be anionic (negatively charged), cationic (positively charged), or nonionic (neutral).

Asphalt Primer

Low-viscosity asphalt (highly liquid) that penetrates into a nonbituminous surface upon application.

Asphalt Binder

Asphalt cement that is classified according to the Standard Specification for Performance Graded Asphalt Binder, AASHTO Designation MP1. It can be either unmodified or modified asphalt cement, as long as it complies with the specifications.

Asphalt Concrete

A mixture of asphalt binder and aggregate thoroughly mixed and compacted into a mass.

Asphalt Prime Coat

An application of asphalt primer to an absorbent surface. It is used to prepare an untreated base for an asphalt surface. The prime coat penetrates or is mixed into the surface of the base, plugs the voids, and hardens the top and helps bind it to the overlying asphalt course.

Asphalt Rubber Binder (AR)

Conventional asphalt cement to which recycled ground tire rubber has been added, which, when reacting with the hot asphalt cement, causes a swelling and/or dispersion of the tire rubber particles.

Asphalt Leveling Course

A course of hot mix asphalt of variable thickness used to eliminate irregularities in the contour of an existing surface prior to placing the subsequent course.

Asphalt Pavement Structure

A pavement structure that is designed and constructed so that all courses above the subgrade are asphalt concrete (full-depth asphalt pavement).

Asphalt Rubber-Asphalt Concrete (AR-AC)

A high-quality, thoroughly controlled hot mixture of asphalt rubber binder (AR) and well-graded, high-quality aggregate that can be thoroughly compacted into a uniform dense mass.

Asphalt (Asphalt Cement)

A dark brown to black cementitious material in which the predominating constituents are bitumen, which occur in nature or are obtained in petroleum processing. Asphalt is a constituent in varying proportions of most crude petroleum and is used for paving, roofing, industrial uses, and other special purposes.

Asphalt Emulsion Slurry Seal

A mixture of slow-setting emulsified asphalt, fine aggregate and mineral filler with a slurry consistency.

Asphalt Pavement Analyser (APA)

The Asphalt Pavement Analyzer (APA) is a laboratory accelerated loading equipment that can be used to evaluate rutting potential of hot mix asphalt (HMA). The APA is designed to simulate traffic loading created by vehicle wheels. A moving wheel load atop a pressurized rubber hose replicates the repeated loads a pavement will see during its daily cycle. The rate and pressure of the loading is controlled by a dedicated computer, which also acts as data acquisition for the APA. The chamber is also environmentally controlled so rutting potential can be measured for an array of conditions. Engineers can determine the rutting potential of specific asphalt mixtures using the APA as a comparative tool. 

Asphalt Emulsion Mix (Cold)

A mixture of unheated mineral aggregate and emulsified (or cutback) asphalt binder. It can be plant-mixed or mixed in place.

Asphalt Shingle Modifier (ASM)

The term used to describe roofing shingles, which when processed by Lafarge North America provide an additive to be used in the manufacture of HMA. 

Asphaltenes

The high-molecular-weight hydrocarbon fraction precipitated from asphalt by a designated paraffinic naphtha solvent at a specified solvent-asphalt ratio.

Automatic Dryer Control

A system that automatically maintains the temperature of aggregates discharged from the dryer within a preset range.

Automatic Proportioning Control

A system in which proportions of the aggregate and asphalt fractions are controlled by means of gates or valves, which are opened and closed by self-acting mechanical or electronic machinery without any intermediate manual control.

Automatic Cycling Control

A control system in which the opening and closing of the weigh hopper discharge gate, the bituminous discharge valve, and the pug mill discharge gate are actuated by means of self-acting mechanical or electrical machinery without any intermediate manual control. The system includes preset timing devices to control the desired periods of dry and wet mixing cycles.

B

Back-Calculation

An analytical technique used to determine the equivalent elastic moduli of pavement layers corresponding to the measured load and deflections. In the iterative method, layer moduli are selected and adjusted until the difference between the calculated and measured deflections are within selected tolerances, or the maximum number of iterations has been reached.

Bank Gravel

Gravel found in natural deposits, usually intermixed with fine material such as sand or clay or a combination thereof. Bank gravel includes gravelly clay, gravelly sand, clayey gravel, and sandy gravel (the names indicate the relative proportion of the materials in the mixture).

Base Course

The layer in the pavement system immediately below the binder and surface courses. It usually consists of crushed stone, although it may consist of crushed slag or other stabilized or unstabilized material.

Batch Plant

A manufacturing facility for producing asphalt paving mixtures that proportions blending. Batch plants manufacture asphalt in batches rather than continuously and are more suited for small manufacturing runs and (frequent) changes in mixture types.

Binder Course

The HMA course immediately below the surface course, generally consisting of larger aggregates and less asphalt (by weight) than the surface.

Bitumen

A class of black or dark-colored (solid, semisolid, or viscous) cementitious substances, natural or manufactured, composed principally of high-molecular-weight hydrocarbons, of which asphalts, tars, pitches, and asphaltites are typical.

Blast-Furnace Slag

A nonmetallic product, consisting essentially of silicates and alumino-silicates of lime and other bases, that is developed simultaneously with iron in a blast furnace.

Bleeding or Flushing Asphalt

The upward migration of asphalt binder in an asphalt pavement resulting in the formation of asphalt film on the surface.

Blow-Up

The localized buckling or upward movement of a portland cement concrete (PCC) pavement caused primarily by excessive expansion.

Break and Seat

A fractured slab technique used in the rehabilitation of reinforced concrete pavement (RCP) that minimizes slab action by fracturing the portland cement concrete (PCC) layer into smaller segments. This reduction in slab length (and debonding from the reinforcement steel) minimizes reflective cracking in new HMA overlays.

Breaking

The phenomenon of asphalt and water separating in an asphalt emulsion, beginning the curing process. The rate of breaking is controlled primarily by the emulsifying agent and somewhat depends on environmental conditions.

C

California Bearing Ratio (CBR)

A test used for evaluating bases, sub-bases, and subgrades for pavement thickness design. It is a relative measure of the shear resistance of a soil.

Cape Seal

A surface treatment in which a chip seal is followed by the application of either slurry seal or microsurfacing.

Channels (Ruts)

Channeled depressions that sometimes develop in the wheel paths of an asphalt pavement.

Clinker

A fused or partially fused by-product of the combustion of coal. Also includes lava and portland cement and partially vitrified slag and brick.

Coal Tar

A dark brown to black cementitious material produced by the destructive distillation of bituminous coal.

Coarse-Graded Aggregate

Aggregate having a continuous grading in sizes of particles, from coarse through fine, with a predominance of coarse sizes.

Coarse Aggregate

Aggregate retained on the 2.36-millimeter (No. 8) sieve.

Cold In-Place Recycling Train

A unit consisting of a large milling machine towing a screening/crushing plant and pug mill mixer for the addition of asphalt emulsion and production of a cold mix base

Compaction

The act of compressing a given volume of material into a smaller volume.

Consensus Properties

Aggregate characteristics that must follow certain criteria to satisfy a Superpave mix design. Specified test values for these properties are not source specific but widely agreed upon. They include coarse aggregate angularity, fine aggregate angularity, flat or elongated particles, and clay content.

Consistency

The degree of fluidity of asphalt cement at any particular temperature. The consistency of asphalt cement varies with its temperature; therefore, it is necessary to use a common or standard temperature when comparing the consistency of one asphalt cement with another.

Corrugations (Washboarding) and Shoving

A type of pavement distortion. Corrugation is a form of plastic deformation typified by ripples across the pavement surface. These distortions usually occur at points where traffic starts and stops, on hills where vehicles break on the downgrade, on sharp curves, or where vehicles hit a bump and bounce up and down. They occur in asphalt layers that lack stability.

Crack

An approximately vertical random cleavage of the pavement caused by traffic loading, thermal stresses, and/or aging of the binder.

Crack-Relief Layer

A large stone, open graded asphalt mixture placed over a distressed pavement that minimizes reflective cracking by absorbing the energy produced by movement in the underlying pavement.

Crack and Seat

A fractured slab technique used in the rehabilitation of portland cement concrete (PCC) pavements that minimizes slab action in a jointed concrete pavement (JCP) by fracturing the PCC layer into smaller segments. This reduction in slab length minimizes reflective cracking in new HMA overlays.

Crusher-Run

The total unscreened product of a stone crusher.

Curing

The development of the mechanical properties of the asphalt binder. This occurs after the emulsion has broken and the emulsion particles coalesce and bond to the aggregate.

Cutback Asphalt

Asphalt cement that has been liquefied by blending with petroleum solvents (diluents). Upon exposure to atmospheric conditions, the diluents evaporate, leaving the asphalt cement to perform its function.

D

Deep-Strength Asphalt Pavement

Pavements containing at least four inches of HMA over nonstabilized base courses.

Deflection, Representative Rebound

The mean value of measured rebound deflections in a test section, plus two standard deviations, adjusted for temperature and the most critical period of the year for pavement performance.

Deflection Sensor

The term used to refer to the electronic device(s) capable of measuring the vertical movement of the pavement and mounted in such a manner as to minimize angular rotation with respect to its measuring plane at the expected movement. Sensor types include seismometers, velocity transducers, and accelerometers.

Deflection

A load-induced, downward movement of a pavement section.

Deflection, Residual

The difference between the original and final elevations of the pavement surface resulting from the application and removal of one or more loads to and from the surface.

Deflection, Rebound

The amount of surface rebound when a load is removed.

Deflection Basin

The idealized shape of the deformed pavement surface as a result of a cyclic or impact load as depicted from the peak measurements of five or more deflection sensors.

Delivery Tolerances

Permissible variations from the exact desired proportions of aggregate and bituminous material as manufactured by an asphalt plant.

Dense-Graded Aggregate

An aggregate that has a particle size distribution such that when it is compacted, the resulting voids between the aggregate particles, expressed as a percentage of the total space occupied by the material, are less than 10 percent.

Densification

The act of increasing the density of a mixture during the compaction process.

Design Period

The number of years from the initial application of traffic until the first planned major resurfacing or overlay. This term should not be confused with pavement life or analysis period. Adding hot mix asphalt overlays as required will extend pavement life indefinitely or until geometric considerations (or other factors) make the pavement obsolete.

Design ESAL

The total number of equivalent 80-kN (18,000-pound), single-axle load applications (equivalent single-axle loads) expected throughout the design period.

Design Subgrade Resilient Modulus

The value of the subgrade resilient modulus (MR) used for designing the pavement structure. It is a percentile value of the subgrade resilient modulus test data distribution that varies with design ESAL. 

Design Lane

The lane on which the greatest number of equivalent 80-kN (18,000-pound) single-axle loads (ESALs) is expected. This will normally be either lane of a two-lane roadway or the outside lane of a multilane highway.

Disintegration

The breaking up of a pavement into small, loose fragments caused by traffic or weathering (for example, raveling).

Distortion

Any change of a pavement surface from its original shape.

Drum Mix Plant

A manufacturing facility for producing asphalt paving mixtures that proportions the aggregate, then dries and coats the aggregate with a proportional amount of asphalt in the same drum. Variations of this type of plant use several types of drum modifications, separate (and smaller) mixing drums, and coating units (coaters) to accomplish the mixing process. They are more suited for long runs of the same product.

Dryer

An apparatus that will dry the aggregates and heat them to specified temperatures.

Ductility

The ability of a substance to be drawn out or stretched thin. While ductility is considered an important characteristic of asphalt cements in many applications, the presence or absence of ductility is usually considered more significant than the actual degree of ductility.

Durability

The property of an asphalt pavement that represents its ability to resist disintegration by weathering and traffic.

E

ESAL (equivalent single-axle load)

The effect on pavement performance of any combination of axle loads of varying magnitude equated to the number of 80-kN (18,000-lb.) single-axle loads that are required to produce an equivalent effect.

Edge Joint Cracks

The separation of the joint between the pavement and the shoulder, commonly caused by the alternate wetting and drying beneath the shoulder surface. Other causes are shoulder settlement, mix shrinkage, and trucks straddling the joint.

Effective Thickness

The ratio of the thickness of an existing pavement material compared with the equivalent thickness of a new HMA layer.

Emulsifying Agent or Emulsifier

The chemical added to the water and asphalt that keeps the asphalt in stable suspension in the water. The emulsifier determines the charge of the emulsion and controls the breaking rate.

F

Fatigue Resistance

The ability of asphalt pavement to resist crack initiation caused by repeated flexing.

Fine Aggregate

Aggregate passing through the 2.36-millimeter (No. 8) sieve.

Fine-Graded Aggregate

One having a continuous grading in sizes of particles from coarse through fine with a predominance of fine sizes.

Flexibility

The ability of an asphalt pavement structure to conform to settlement of the foundation. Generally, flexibility of the asphalt paving mixture is enhanced by high asphalt content.

Flexible pavement

Pavements that are surfaced with bituminous (or asphalt) materials in the surface course. These can be in the form of pavement surfaces such as a bituminous surface course (BST), generally found on lower volume (or lower traffic) roads, or hot mix asphalt (HMA) surfaces generally used on higher volume roads. These types of pavements are called "flexible" since the total pavement structure "bends" or "deflects" due to traffic loads.

Fog Seal

A light application of diluted asphalt emulsion. It is used to renew old asphalt surfaces, seal small cracks and surface voids, and inhibit raveling.

Fractured Slab Techniques

Processes used to rehabilitate portland cement concrete (PCC) pavements by eliminating slab action through the reduction of slab size (crack/break and seat) or the pulverization of the PCC slab (rubblization) into essentially a granular base.

Full-Depth Asphalt Pavement

The term full-depth (registered by the Asphalt Institute with the U.S. Patent Office) certifies that the pavement is one in which asphalt mixtures are employed for all courses above the subgrade or improved subgrade. A full-depth asphalt pavement is placed directly on the prepared subgrade.

G

Geotextiles

Fabric-like materials used in the paving process. Geotextiles are manufactured for specific uses and performance characteristics. Some uses include stabilization of base material to prevent migration into sub-grades, retarding of reflective cracking in asphalt overlays, and serving as a moisture barrier between pavement layers.

Grade Depressions

Localized low areas of limited size.

H

Heavy Trucks

Two-axle, six-tire trucks or larger. Pickup, panel, and light four-tire trucks are not included. Trucks with heavy-duty, wide-base tires are included.

Hot Mix Asphalt (HMA)

High-quality, thoroughly controlled hot mixture of asphalt binder (cement) and well-graded, high-quality aggregate, which can be compacted into a uniform dense mass.

Hot Aggregate Storage Bins

Bins that store heated and fractionated aggregates prior to their final proportioning into the mixer.

Hot Mix Asphalt (HMA) Overlay

One or more courses of HMA over an existing pavement.

I

Impermeability

The resistance of an asphalt pavement to the passage of air and water into or through the pavement.

J

JMF

Job-mix formula. A recommended/specified mixture of aggregate and asphalt binder.

K

Kinematic Viscosity

A measure of the viscosity of asphalt, measured in centistokes, conducted at a temperature of 135 degrees C (275 degrees F).

L

Lane Joint Cracks

Longitudinal separations along the seam between two paving lanes.

Leveling course

A first lift applied to an existing pavement used to fill in ruts and make up elevation differences.

Lift

A layer or course of paving material applied to a base or a previous layer.

Lime-Fly Ash Base

A road base material consisting of a blend of mineral aggregate, lime, fly ash, and water, which when combined in proper proportions and compacted produces a dense mass of increased strength. 

Lime Treated Subgrade

A subgrade preparation technique in which the subgrade soil and added lime are mechanically mixed and compacted to produce a higher-modulus base material than the in situ material.

Liquid limit

The water content above which soil behaves as a viscous liquid.

Load Equivalency Factor (LEF)

The equivalent number of 80-kN (18,000-pound) single-axle load (ESAL) applications contributed by one passage of an axle.

Longitudinal Crack

A vertical crack in the pavement that follows a course approximately parallel to the centerline.

M

MTV – Material Transfer Vehicle

Used to assist the paver in accepting HMA. Most pavers are equipped to receive HMA directly, however in certain situations it can be necessary or advantageous to use an MTV. Paving using bottom dump trucks and windrows requires a windrow elevator MTV while other MTVs are used to provide additional surge volume, which is advantageous because it allows the paver to operate continuously without stopping, minimizes truck waiting time at the paving site, and may minimize segregation and temperature differentials.

Macadam

Type of early bituminous pavement named after its inventor, a Scotsman named John McAdam (1756-1836). McAdam (sometimes spelled "Macadam") pavements used smaller angular aggregate over larger angular aggregate over a well-compacted, sloped subgrade.

Maintenance Mix

A mixture of asphalt emulsion and mineral aggregate for use in relatively small areas to patch holes, depressions, and distressed areas in existing pavements. Appropriate hand or mechanical methods are used in placing and compacting the mix.

Maintenance Mix

A mixture of asphalt emulsion and mineral aggregate for use in relatively small areas to patch holes, depressions, and distressed areas in existing pavements. Appropriate hand or mechanical methods are used in placing and compacting the mix.

Mechanical Spreaders

Spreader boxes that are mounted on wheels. The spreaders are attached to and pushed by dump trucks (HMA boxes are pulled and chip spreaders are pushed).

Medium-Curing (MC) Asphalt

Cutback asphalt composed of asphalt cement and a diluent of medium volatility.

Mesh

The square opening of a sieve.

Microsurfacing

A mixture of polymer-modified asphalt emulsion, crushed dense graded aggregate, mineral filler, additives, and water. It provides a thin resurfacing of 10 to 20 millimeters (3/8 to 3/4 inch) to the pavement.

Milling Machine

A self-propelled unit having a cutting head equipped with carbide-tipped tools for the pulverization and removal of layers of asphalt materials from pavements.

Mineral Filler

A finely divided mineral product, at least 70 percent of which will pass a 0.075-millimeter (No. 200) sieve. Pulverized limestone is the most commonly manufactured filler, although other stone dust, hydrated lime, portland cement, and certain natural deposits of finely divided mineral matter are also used.

Mineral Dust

The portion of fine aggregate passing the 0.075-millimeter (No. 200) sieve.

Modified Asphalt Rubber-Asphalt Concrete (MAR-AC)

High-quality, thoroughly controlled hot mixture of modified asphalt rubber (AR) binder and well-graded, high-quality aggregate, which can be thoroughly compacted into a uniformly dense mass.

Modified Asphalt Rubber (MAR) Binder

Conventional asphalt cement to which recycled ground tire rubber and compounds have been added, which when made to react with hot asphalt cement causes a dispersion of the tire rubber particles and compounds.

Multiple Surface Treatments

Two surface treatments placed one atop the other. The aggregate maximum size of each successive treatment is usually one-half the previous one. A multiple surface treatment may comprise a series of single treatments that produces a pavement course up to 25 millimeters (one inch) in thickness. A multiple surface treatment is a denser wearing and waterproofing course than a single surface treatment.

N

Natural (Native) Asphalt

Asphalt occurring in nature, which has been derived from petroleum through natural processes of evaporation of volatile fractions, leaving the asphalt fractions. The native asphalt of most significance is found in the Trinidad and Bermudez Lake (Venezuela) deposits.

Nondestructive Testing (NDT)

In the context of pavement evaluation, NDT is deflection testing, without destruction of the pavement, to determine a pavement's response to pavement loading.

O

Open-Graded Asphalt Friction Course

A pavement surface course consisting of a high-void asphalt plant mix that permits rapid drainage of rainwater through the course and out the shoulder. The mixture is characterized by a large percentage of one-sized coarse aggregate. This course prevents tires from hydroplaning and provides a skid-resistant pavement surface with significant noise reduction.

Open-Graded Aggregate

An aggregate containing less-fine aggregate in which the void spaces in the compacted aggregate are relatively large and interconnected.

P

Pascal-Seconds

The SI unit for viscosity; 1 Pascal-second equals 10 poises.

Pavement Structure

The entire pavement system of selected materials, from subgrade to surface.

Pavement Base

The lower or underlying pavement course atop the sub-base or subgrade and under the top or wearing course.

Penetration

The consistency of a bituminous material expressed as the distance (in tenths of a millimeter) that a standard needle penetrates a sample vertically under specified conditions of loading, time, and temperature.

Penetration Grading

A classification system of asphalt cements based on penetration in tenths of a millimeter at 25 degrees C (77 degrees F). There are five standard penetration grades for paving: 40-50, 60-70, 85-100, 120-150, and 200-300.

Performance Graded (PG)

Asphalt binder grade designation used in Superpave. It is based on the binder's mechanical performance under critical temperatures and aging conditions. EX: Performance Graded Asphalt Cements (PGAC)

Planned-Stage Construction

A construction process in which stages of the project are performed sequentially according to design and a predetermined time schedule.

Plant Mix Base

A foundation course produced in an asphalt mixing plant that consists of a mineral aggregate uniformly coated with asphalt cement or emulsified asphalt.

Plant Screens

Screens located between the dryer and hot bins that separate heated aggregates into proper hot bin sizes.

Plant Mix (Cold)

A mixture of emulsified (or cutback) asphalt and unheated mineral aggregate prepared in a central mixing plant and spread and compacted with conventional paving equipment while the mixture is at or near ambient temperature.

Plastic Limit

The water content below which a soil ceases to behave as a plastic medium and beings to exhibit the properties of a semisolid.

Plasticity Index (PI)

The numerical difference between the Liquid Limit and the Plastic Limit of a soil.

Poise

A centimeter-gram-second unit of absolute viscosity equal to the viscosity of a fluid in which a value of stress of one dyne per square centimeter is required to maintain a difference of velocity of 1 centimeter per second between two parallel planes in the fluid that lie in the direction of flow and are separated by a distance of 1 centimeter.

Polished Aggregate

Aggregate particles in a pavement surface that have been worn smooth by traffic.

Polymer-Modified Asphalt (PMA) Binder

Conventional asphalt cement to which one or more polymer compounds have been added to improve resistance to deformation at high pavement temperatures and often also offer cracking resistance at low temperatures.

Potholes

Bowl-shaped openings in the pavement resulting from localized disintegration.

Power Sweeper

A power-operated rotary broom used to clean loose material from the pavement surface.

Present Serviceability Rating (PSR)

The rating assigned to a specific pavement section.

Present Serviceability Index (PSI)

A mathematical combination of values obtained from certain physical measurements of a large number of pavements, so formulated as to determine, within prescribed limits, the Present Serviceability Rating (PSR) for those pavements.

Present Serviceability

The ability of a specific section of pavement to serve its intended use in its existing condition.

Pug Mill

Alternative name for the mixing chamber on an asphalt batch plant.

Pumping

Slab deflection under passing loads sometimes resulting in the discharge of water and subgrade soils along joints, cracks, and pavement edges.

Q

Quality assurance

The planned and systematic actions necessary to provide confidence that a product or facility will perform satisfactorily in service. Quality assurance addresses the overall problem of obtaining the quality of a service, product, or facility in the most efficient, economical, and satisfactory manner possible.

Quality control

Those quality assurance actions and considerations necessary to assess production and construction processes so as to control the level of quality being produced in the end product. This concept of quality control includes sampling and testing to monitor the process but usually does not include acceptance sampling and testing.

R

Rapid-Curing (RC) Asphalt

Cutback asphalt composed of asphalt cement and a naphtha or gasoline-type diluent of high volatility.

Raveling

The progressive separation of aggregate particles in a pavement from the surface downward or from the edges inward.

Reclaimed Asphalt Pavement (RAP)

Excavated asphalt pavement that has been pulverized, usually by milling, and is used like an aggregate in the recycling of asphalt pavements.

Reclaiming Machine

A self-propelled unit having a transverse cutting and mixing head inside of a closed chamber for the pulverization and mixing of existing pavement materials with asphalt emulsion. Asphalt emulsion (and mixing water) may be added directly through the machine by a liquid additive system and spray bar.

Recycled Asphalt Mix

A mixture produced after processing existing asphalt pavement materials. The recycled mix may be produced by hot or cold mixing at a plant, or by processing the materials cold and in place.

Reflection Cracks

Cracks in asphalt overlays (usually over deteriorated portland cement concrete [PCC] pavements) that reflect the crack pattern in the pavement structure below it.

Residue

The asphalt binder that remains from an asphalt emulsion after the emulsifying agent has broken and cured, or the remains of a cutback after the volatiles have cured.

Resilient Modulus of Elasticity (MR)

A laboratory measurement of the behavior of pavement materials to characterize their stiffness and resiliency (see Soils Manual, MS-10). A confined or unconfined test specimen (core or recompacted) is repeatedly loaded and unloaded at a prescribed rate. The resilient modulus is a function of load duration, load frequency, and number of loading cycles.

Resistance Value (R-value)

A test for evaluating bases, sub-bases, and subgrades for pavement thickness design.

Roadway

All facilities on which motor vehicles are intended to travel, such as secondary roads, interstate highways, streets, and parking lots.

Roughometer

An instrumented, single-wheel trailer that measures the roughness of a pavement surface in accumulated millimeters or inches per mile.

Rubblization

The pulverization of a portland cement concrete (PCC) pavement into smaller particles, reducing the existing pavement layer to a sound, structural base that will be compatible with an asphalt overlay.

Rutting

Surface depression in the wheelpath of a pavement

S

Sand

Fine aggregate (any fraction below a No. 8 sieve) resulting from natural disintegration and abrasion or processing of rock.

Sand Asphalt

A mixture of sand and asphalt cement, cutback asphalt, or emulsified asphalt. It may be prepared with sand or clay or combinations thereof, including gravelly clay, gravelly sand, clayey gravel, and sandy gravel (the names indicate the relative proportions of the materials in the mixture). Either mixing in place or plant mix formation may be employed. Sand asphalt is used in the construction of both base and surface courses and may or may not contain mineral filler.

Sandwich Seal

A surface treatment consisting of the application of a large aggregate, followed by a spray-applied asphalt emulsion, and covered with a smaller aggregate.

Sandy Soil

A material consisting essentially of fine aggregate particles smaller than the openings in a 2.36-millimeter (No. 8) sieve and usually containing material that can pass through a 0.075-millimeter (No. 200) sieve. This material usually exhibits some plasticity characteristics.

Saw-Cut and Seal

A method of controlling reflective cracking in HMA overlays that involves constructing joints in the new overlay exactly over the joints in the existing pavement.

Scaling

The peeling away or disintegration of the surface of portland cement concrete (PCC).

Screed

The part of a paving machine that spreads, smoothes, and provides initial compaction of the HMA.

Seal Coat

A thin surface treatment used to improve the surface texture and protect an asphalt surface. The main types of seal coats are fog seals, sand seals, slurry seals, microsurfacing, cape seals, sandwich seals, and chip seals.

Segregation

Segregation is the non-uniform distribution of coarse and fine aggregate components within the asphalt mixture.

Self-Propelled Spreaders

Spreaders having their own power units and two hoppers. The spreader pulls the truck as it dumps its load into the receiving hopper. Conveyor belts move the aggregate forward to the spreading hopper.

Sheet Asphalt

A hot mixture of asphalt binder with clean, angular, graded sand and mineral filler. Its use is ordinarily confined to reservoir liners and landfill caps. It is usually laid on an intermediate or leveling course.

Shoving

A form of plastic movement resulting in localized bulging of the pavement.

Shrinkage Cracks

Interconnected cracks forming a series of large blocks, usually with sharp corners or angles.

Sieve

An apparatus for laboratory work in which the openings in the mesh are square for separating sizes of material.

Single-Surface Treatment

A single application of asphalt to a road surface followed immediately by a single layer of aggregate. The thickness of the treatment is about the same as that of the nominal, maximum-sized aggregate particles.

Skid Hazard

Any condition that might contribute to the reduction of friction forces on the pavement surface.

Skid Resistance

The ability of a paved surface, particularly when wet, to offer resistance to slipping or skidding. Proper asphalt content and aggregate with a rough surface texture are the greatest contributors. The aggregate must not only have a rough surface texture, but also resist polishing.

Slippage Cracks

Crescent-shaped cracks resulting from traffic-induced horizontal forces that are open in the direction of the thrust of wheels on the pavement surface. They result when severe or repeated shear stresses are applied to the surface and there is a lack of bond between the surface layer and the course beneath.

Slow-Curing (SC) Asphalt

Cutback asphalt composed of asphalt cement and oils of low volatility.

Slurry Seal

A mixture of emulsified asphalt, well-graded fine aggregate, mineral filler or other additives, and water. A slurry seal will fill minor cracks, restore a uniform surface texture, and restore friction values.

Soil/Cement Base

A hardened material formed by curing a mechanically mixed and compacted mixture of pulverized soil, portland cement, and water used as a layer in a pavement system to reinforce and protect the subgrade or sub-base.

Solubility

A measure of the purity of asphalt cement. The ability of the portion of the asphalt cement that is soluble to be dissolved in a specified solvent.

Source Properties

Aggregate characteristics that must meet certain criteria to satisfy a Superpave mix design. Specified values are established by local agencies. They include toughness, soundness, and deleterious materials.

Spalling

The breaking or chipping of a portland cement concrete (PCC) pavement at joints, cracks, or edges, usually resulting in fragments with feather edges.

Stability

The ability of an asphalt paving mixture to resist deformation from imposed loads. Stability depends on both internal friction and cohesion.

Stationary Plants

Asphalt plants that are so constructed that moving them is not considered economically feasible.

Steel-Wheel Vibratory Rollers

A compactor having single or double cylindrical steel rolls that apply compactive effort with weight and vibration. The amount of compactive force is adjusted by changing the frequency and amplitude of vibration.

Steel-Wheel Static Rollers

Tandem or three-wheel rollers with cylindrical steel rolls that apply their weight directly to the pavement.

Stoke

A unit of kinematic viscosity equal to the viscosity of a fluid in poises divided by the density of the fluid in grams per cubic centimeter.

Structural Overlay

An HMA overlay constructed for the purpose of increasing the structural value and ride quality of the pavement system.

Sub-base

The course in the asphalt pavement structure immediately below the base course. If the subgrade soil has adequate support, it may serve as the sub-base.

Subgrade Resilient Modulus

The modulus of the subgrade determined by repeated load, triaxial compression tests on soil samples. It is the ratio of the amplitude of the accepted axial stress to the amplitude of the resultant recoverable axial strain, generally designated by the symbol MR.

Subgrade

The soil prepared to support a pavement structure or a pavement system. It is the foundation of the pavement structure.

Subgrade, Improved

Subgrade that has been improved as a working platform by (1) the incorporation of granular materials or stabilizers such as asphalt, lime, or portland cement into the subgrade soil; or (2) any course of select or improved material placed on the subgrade soil below the pavement structure.

Superpave Gyratory Compactor (SGC)

A device used during Superpave mix design or quality-control activities for compacting samples of hot mix asphalt into specimens used for volumetric analysis. Continuous densification of the specimen is measured during the compaction process.

Superpave Mix Design

An asphalt mixture design system that integrates the selection of materials (asphalt, aggregate) and volumetric proportioning with the project's climate and design traffic.

Superpave,™

Short for "Superior Performing Asphalt Pavement, Superpave is a performance-based system for selecting and specifying asphalt binders and for designing asphalt mixtures.

T

Tensile Strength Ratio

The tensile strength ratio (TSR) is the ratio of average tensile strength after conditioning to that before conditioning, expressed as a percent

The test is performed by compacting specimens to an air void level of 6 to 8 percent. Three specimens are selected as a control and tested without moisture conditioning, and three more specimens are selected to be conditioned by saturating with water undergoing a freeze cycle, and subsequently having a warm-water soaking cycle. The specimens are then tested for indirect tensile strength by loading the specimens at a constant rate and measuring the force required to break the specimen. The tensile strength of the conditioned specimens is compared to the control specimens to determine the tensile strength ratio (TSR).

Thermal cracking

Cracking caused by shrinkage of the pavement surface due to low temperatures.

Transverse Crack

A crack that follows a course approximately at right angles to the centerline.

Travel Plants

Self-propelled plants that proportion and mix aggregates and asphalt as they move along the road. There are three general types of travel plants:

 

1. One that moves through a prepared aggregate windrow on the roadbed, adds and mixes the asphalt as it goes, and rear-discharges a mixed windrow ready for aeration and spreading.

2. One that receives aggregate into its hopper from haul trucks, adds and mixes asphalt, and spreads the mix to the rear as it moves along the roadbed.
3. Batch mixing units, such as slurry machines, that haul materials to the site and then mix and apply the materials.

Truck Factor

The number of ESALs contributed by one passage of a vehicle. Truck factors can apply to vehicles of a single type or class or to a group of vehicles of different types.

U

Upheaval

The localized upward displacement of a pavement due to swelling of the subgrade or some portion of the pavement structure.

V

Viscosity

A measure of a liquid's resistance to flow with respect to time.

Viscosity Grading

A classification system of asphalt cements based on viscosity ranges at 60 degrees C (140 degrees F). A minimum viscosity at 135 degrees C (275 degrees F) is also usually specified. The purpose is to prescribe limiting values of consistency at these two temperatures. Sixty degrees C (140 degrees F) approximates the maximum temperature of an asphalt pavement surface in service in the United States; 135 degrees C (275 degrees F) approximates the mixing and laydown temperatures for hot mix asphalt pavements.

Voids in Mineral Aggregate (VMA)

The volume of intergranular void space between the aggregate particles of a compacted paving mixture that includes the air voids and the effective asphalt content, expressed as a percent of the total volume of the specimen.

W

Well-Graded Aggregate

Aggregate graded with relatively uniform proportions, from the maximum size down to the filler.

Wet Mixing Period

The interval of time between the beginning of application of asphalt material into a pug mill and the opening of the discharge gate.

Whirl Spreaders

Spreaders that are attached to or are built onto dump trucks. Aggregate is fed onto the spreader disc through an adjustable opening. The speed of the disc controls the width of spread.

Workability

The ease with which paving mixtures may be placed and compacted.

  • Print
  • Bookmark

Durapave®

Lafarge Asphalt is committed to being North America's leading developer and supplier of innovative Asphalt products designed to optimize quality, performance, durability, and sustainability. Each of the products in our Durapave® series offers unique performance characteristics designed to address a range of needs such as moisture damage, high axle loading and sound attenuation. At the heart of all of our Asphalt products is research, testing  and development, ensuring the highest end performance is delivered.

Social media
Lafarge on Facebook Lafarge on Twitter Lafarge on You tube
LafargeHolcim. Cement, aggregates, Concrete.